REPRESENTATIVE OFFICE
IN YOUR REGION
VMP Holding CISC
Ekaterinburg,
25 Tkachey str.,

tel.: +7 343 357-30-97,
+7 343 357-30-79
e-mail: office@fmp.ru



VMP in social networks:

QUICK-DRYING
MATERIAL
ATMOSPHERE-RESISTANT
MATERIAL
HEAT-RESISTANT
MATERIAL
THICK-LAYERED
MATERIAL
FOR APPLICATION AT
NEGATIVE
TEMPERATURE
SINGLE-PACKED
MATERIAL
ST 2, ST 3 SURFACE
PREPARATION DEGREE
FOR USE AT
SEA AND FRESH
WATER
FOR USE WHEN
EXPOSED TO OIL
AND OIL PRODUCTS
ZINC-FILLED
MATERIAL
MATERIAL WITH
ANTICORROSIVE
PIGMENTS
MATERIAL WITH
CORROSION INHIBITOR
MATERIAL WITH
ANTISTATIC PROPERTIES

VINICOR®-62 type B

VINICOR-62 type B
TU 20.30.12-001-54359536-2018
Epoxy-vinyl enamel
Double-packed
Colour: Red-brown, green, gray, black, and other

Description

Double-packed epoxy-vinyl enamel.

Recommended use 

Protective and decorative painting of  anticorrosive  coating systems of ship structures, used in sea and fresh water, including underwater and above-water body, boot topping, metal deck, tanks, deep tanks, battery rooms and other metal  structures  used  in atmospheric  conditions of all macroclimate  areas, atmosphere types and placement categories according to GOST 15150.  Coating: oil-,  gasoline-proof, resistant to spills of oil and petroleum products, sea and fresh water, short-term exposure to hot water and steam, aggressive environments, sudden temperature changes (from minus 60 to plus 60 °C).
Used as a finishing layer in complex coating systems with VINICOR-061 (TU 20.30.12-001-54359536-2018), VINICOR-marine (TU 20.30.12-004-67503963-2018), VINICOR-ecoprime (TU 2312-002-67503963-2011) primers, with VINICOR-63 (TU 2313-007-67503963-2013) varnish, as well as with other  primers on 
vinyl-epoxy and epoxy bases.

Certificates, Approvals

State registration certificate No. RU. 78.01.06.008.Е.000564.12.18 dated 11.12.2018 It has a certificate of voluntary certification system of the Russian River Register No. POCC RU.PO00.H00269.

Surface preparation

The surface prepared for applying varnish coat should be cleaned from dirt, degreased, if necessary, dust and moisture shall be removed.

Application 

  • mix the base thoroughly to homogenous condition before application;
  • with constant stirring, add a hardener to the base and mix thoroughly.
The mixing ratio of the base and hardener EN-02, EN-03 (by mass) 100:2.46 respectively;
  • if necessary, the composition should be diluted to the working viscosity.
The material is recommended  to be applied  in the plant  and field  conditions, dark colors at temperature  from  minus  10  to  plus  35  °C  and light colors at temperature from minus 5 to plus  35 °C at relative air humidity not more than 85 %.
The temperature of the painted surface shall be above the dew point by at least 3 °C. 
Prepared enamel shall be of temperature at least 15 °C.
The enamel  is recommended to be applied in  2-3  layers using airless,  conventional  (air) spray  by brush/roller.
The overlapping interval  between the layers of enamel at a temperature  (20±2)°C  –  not less than 3 hours. Hardening time depends on the temperature of the surface and ambient air, degree of dilution of the material, thickness of the coating, efficiency of ventilation and relative air humidity.
Holding time  of the coating  before operating in aggressive conditions is not less than 7 days at temperature from 15 to 22 °С.

Storage and handling

The material  is delivered in packages: base and hardener packed in metal buckets and metal cans respectively depending on the set weight.
Storage conditions of the  enamel components –  according to GOST 9980.5 (at air temperature from minus 40 to plus 40  °C). The container shall be protected from atmospheric condensation and direct sunlight.
The shelf life  is determined by warranty storage of the base (24 months) and hardener ( 12 months) starting with the manufacture date.

Precautions

When working with  the  material,  one shall observe the existing sectoral standard norms and requirements and safety measures as specified on the package label.
One shall use personal protective equipment (goggles, face masks and respirators) and avoid inhalation of  thinners  and contact of the composition  or its components  with skin, eye mucosa, respiratory channels; use inside the premises is allowed only in case sufficient ventilation is provided.
The material and its components (base and hardener) are fire-hazardous!

The information is of general character, without consideration to the object specific nature. Use of materials for other purposes not specified here or in case other influencing factors are present shall be approved by the  VMP Holding CJSC  in writing. In case of absence of such approval the manufacturer is not held liable for the improper use of the material and the buyer falls from the right to present claims connected with the coating quality.

Compatible materials:

You can order products and get advice of how to use materials by calling: 8-800-500-54-00, +7 343 357-30-97, 385-79-00 or by sending an On-line request

You can also purchase products from official representatives of the VMP in Russian regions, countries of near and far abroad.