REPRESENTATIVE OFFICE
IN YOUR REGION
VMP Holding CISC
Ekaterinburg,
25 Tkachey str.,

tel.: +7 343 357-30-97,
+7 343 357-30-79
e-mail: office@fmp.ru



VMP in social networks:

QUICK-DRYING
MATERIAL
ATMOSPHERE-RESISTANT
MATERIAL
HEAT-RESISTANT
MATERIAL
THICK-LAYERED
MATERIAL
FOR APPLICATION AT
NEGATIVE
TEMPERATURE
SINGLE-PACKED
MATERIAL
ST 2, ST 3 SURFACE
PREPARATION DEGREE
FOR USE AT
SEA AND FRESH
WATER
FOR USE WHEN
EXPOSED TO OIL
AND OIL PRODUCTS
ZINC-FILLED
MATERIAL
MATERIAL WITH
ANTICORROSIVE
PIGMENTS
MATERIAL WITH
CORROSION INHIBITOR
MATERIAL WITH
ANTISTATIC PROPERTIES
ZFES-A
TU 20.30.12-092-12288779-2017
Protective-frictional composition
Double-packed
Colour: Semi-transparent rough-surfaced

Description

Double-packed composition consists of polymer ink containing dispersed abrasive material and ethyl silicate binding agent.

Recommended use

ZFES-A composition is designed to increase the friction coefficient of friction joints contact surfaces of steel structures on high-strength bolts. It is applied only in the complex coating with the ZFES zinc-rich primer (TU 20.30.12-004-12288779-2017). For the period of interoperational storage of structures, the coating provides additional protection against weather impact.
ZFES+ZFES-A complex coating is designed for operation in the atmospheric conditions of all macroclimatic regions, types of atmosphere and placement categories according to GOST 15150.

Certificates, approvals

Certificate of state registration No. RU.66.01.40.015.Е.000122.07.18 dated 05.07.2018

Technical data

 Composition
 Density, g/cm3  0,9-1,1 г/см3
 Non-volatile matters, %  29,0-34,0 %
 Viscosity  thixotropic
 Pot life after mixing, h  8, not less than
 Drying time to 3 degree (GOST 19007-73) at temperature
 (20±2)°С and relative air humidity (65±5)%, min
 30, not more than

Surface preparation

Priming zinc-rich ZFES coating should be cleaned of impurities, if necessary degreased with aqueous solutions of detergents with a pH of 6 to 8 (allow light degreasing with white spirit) and free of dust.

Application

  • mix the composition base (polymer ink) thoroughly to a homogenous condition;
  • add the binding agent in the mass proportion of 100:13.4 with constant mixing;
  • dilute with SOLV-ES solvent (TU 2319-080-12288779-2009) by 10 % by mass;
  • mix to a homogenous condition repetitively actually before application.
The composition should be applied in one layer by air spray (if necessary - with a roller or brush) at a temperature from minus 15°С to plus 40°С and relative humidity of air from 30 % to 80 % (aimed from 50 % to 80 %).
When painting, it is necessary to use paint-spray guns with an upper tank, working on the technology HVLP (high volume, low pressure)

Storage and handling

The composition is delivered in packages: base packed in metal buckets or cans (depending on the weight) and binding agent packed in metal cans.
Storage and transportation conditions of composition – according to GOST 9980.5-2009 – (at air temperature from minus 40 °C to plus 40 °C). The composition and its components must be stored in the hermetically enclosed original container away from heat sources. The container with composition components shall be protected from atmospheric condensation and direct sunlight.
The shelf life of composition components in the hermetically enclosed original container is 6 months starting with the manufacture date.

Precautions

When working with the composition, one shall observe the existing sectoral standard norms and requirements and safety measures as specified on the package label.
Personal protective equipment (goggles, face masks and respirators) shall be used, inhalation of thinners and contact of the composition or its components with skin, ocular mucosa, respiratory channels shall be avoided; use inside the premises is allowed only in case sufficient ventilation is provided.
The composition is classified as a fire-hazardous material. 


The information is of general character, without consideration to the object specific nature. Use of materials for other purposes not specified here or in case other influencing factors are present shall be approved by the VMP Holding CJSC in writing. In case of absence of such approval the manufacturer is not held liable for the improper use of the material and the buyer falls from the right to present claims connected with the coating quality.

Compatible materials:

You can order products and get advice of how to use materials by calling: 8-800-500-54-00, +7 343 357-30-97, 385-79-00 or by sending an On-line request

You can also purchase products from official representatives of the VMP in Russian regions, countries of near and far abroad.