REPRESENTATIVE OFFICE
IN YOUR REGION
VMP Holding CISC
Ekaterinburg,
25 Tkachey str.,

tel.: +7 343 357-30-97,
+7 343 357-30-79
e-mail: office@fmp.ru



VMP in social networks:

QUICK-DRYING
MATERIAL
ATMOSPHERE-RESISTANT
MATERIAL
HEAT-RESISTANT
MATERIAL
THICK-LAYERED
MATERIAL
FOR APPLICATION AT
NEGATIVE
TEMPERATURE
SINGLE-PACKED
MATERIAL
ST 2, ST 3 SURFACE
PREPARATION DEGREE
FOR USE AT
SEA AND FRESH
WATER
FOR USE WHEN
EXPOSED TO OIL
AND OIL PRODUCTS
ZINC-FILLED
MATERIAL
MATERIAL WITH
ANTICORROSIVE
PIGMENTS
MATERIAL WITH
CORROSION INHIBITOR
MATERIAL WITH
ANTISTATIC PROPERTIES
MainAnticorrosive protectionAnticorrosive materialsBY MATERIALEnamelVINICOR®-marine enamel

VINICOR®-marine enamel

VINICOR-marine enamel
TU 20.30.12-004-67503963-2018
Epoxy enamel
Double-packed
Colour: gray, black, red-brown and other colors by agreement with the client

Description

Double-packed epoxy  enamel,  thixotropic,  with  low content of organic solvents, allows to apply thick coating.  VINICOR-marine  coating  is resistant to sea and fresh water, crude oil, oil products, and other environments, sudden temperature changes from minus 50 ºС to plus 60 ºС.

Recommended use 

Is applied as a  finishing  protective  coating  with VINICOR-marine  primer  in complex  corrosion protection systems  of underwater hull and freeboard, variable waterline area, superstructures of unrestricted navigation ships,  hydrotechnical constructions,  and metal structures used in  sea, fresh water and atmospheric conditions (in lack or low intensity of UV-radiation).

Certificates, Approvals

State registration certificate No. RU.77.01.34.008.E.003541.12.18 dated 20.12.2018.
VINICOR-marine  coating system  is  approved by FSUE “Prometey”  and has  decision of MVK for use of materials in ship construction.
It has a certificate of Russian River Register voluntary certification system No. РОСС RU.PO00.H00269.

Surface preparation

VINICOR-marine  primer  coating  shall  be clean,  degreased, if required,  oil and dust shall be removed.

Application 

  • mix the base thoroughly to homogenous condition before application;
  • with constant stirring, add the  hardener to the base and mix thoroughly  (the ratio of the base and hardener stated on the label of the package and in the material quality certificate);
  • dilute to working viscosity, if required;
  • before application, the prepared material shall be held for 15-20 minutes covered.
When working, one shall consider decrease in  pot  life  of the composition (after mixing the components) at air temperature increase.
The material is recommended to be applied  in the plant and field conditions at temperature from plus  5 to plus 35  °C and relative air humidity not more than  85%  (application at temperature from minus 5  °C  is allowed). The temperature of the painted surface shall be above the dew point by at least   3 °C.
Prepared enamel shall be of temperature at least 15 °C.
The enamel is recommended to be applied in 1-2 layers using airless spray, by brush/roller.
Drying of the coat is natural.  Intermediate drying between the layers of  the VINICOR-marine enamel at temperature of plus 20 °C is not less than 24 hours.
Holding time of the VINICOR-marine coating system before operating in aggressive environments is not less than 7 days at temperature of 20 °С.

Storage and handling

The material is delivered in packages: the base and hardener packed in metal buckets  and metal cans respectively depending on the package weight.
Storage conditions  –  according to GOST 9980.5 (at air temperature from minus 40 to plus  35  °C). 
The container with the material components shall be stored away from heating sources, protected from atmospheric condensation and direct sunlight.
The  shelf life  is determined by the storage period of  the base  (24 months)  and  the  hardener (stated in the quality certificate) starting with the manufacture date.

Precautions

When working, one shall observe the existing sectoral standard norms and requirements and safety measures as specified on the package label.
One shall use personal protective equipment (goggles, face masks and respirators), avoid inhalation of thinners and contact of the  material  or its components with skin, eye mucosa, respiratory channels; use inside the premises is allowed only in case sufficient ventilation is provided.
The material and its components (the base and hardener) are fire-hazardous!
Hardened coating is not harmful.

The information is of general character, without consideration to the object specific nature. Use of materials for other purposes not specified here or in case other influencing factors are present shall be approved by the  VMP Holding CJSC  in writing. In case of absence of such approval the manufacturer is not held liable for the improper use of the material and the buyer falls from the right to present claims connected with the coating quality.

Compatible materials:

You can order products and get advice of how to use materials by calling: 8-800-500-54-00, +7 343 357-30-97, 385-79-00 or by sending an On-line request

You can also purchase products from official representatives of the VMP in Russian regions, countries of near and far abroad.