REPRESENTATIVE OFFICE
IN YOUR REGION
VMP Holding CISC
Ekaterinburg,
25 Tkachey str.,

tel.: +7 343 357-30-97,
+7 343 357-30-79
e-mail: office@fmp.ru



VMP in social networks:

QUICK-DRYING
MATERIAL
ATMOSPHERE-RESISTANT
MATERIAL
HEAT-RESISTANT
MATERIAL
THICK-LAYERED
MATERIAL
FOR APPLICATION AT
NEGATIVE
TEMPERATURE
SINGLE-PACKED
MATERIAL
ST 2, ST 3 SURFACE
PREPARATION DEGREE
FOR USE AT
SEA AND FRESH
WATER
FOR USE WHEN
EXPOSED TO OIL
AND OIL PRODUCTS
ZINC-FILLED
MATERIAL
MATERIAL WITH
ANTICORROSIVE
PIGMENTS
MATERIAL WITH
CORROSION INHIBITOR
MATERIAL WITH
ANTISTATIC PROPERTIES

Accelerator of curing

Accelerator of curing

DESCRIPTION

Accelerator of curing is a fatty acid salts solution. 

RECOMMENDED USE

It is recommended in environment of low humidity ratio to reduce drying time of single-packed polyurethane compozitions ZINOTAN (TU 2312-017-12288779-2003), FERROTAN (TU 20.30.12-036-12288779-2018), ALUMOTAN (TU 2312-018-12288779-99), enamels POLYTON-UR (TU 2312-029-12288779-2002) and GOODLINE PU-15 (TU 2312-096-12288779-2014) manufactured by VMP:

 Environmental air parameters                
Temperature, С
Relative humidity, %              
10 20 30 40 50 60 70 80
0 + + + + + + + +
10 + + + +
+ +    
20 + + +          
30 + +            
 Note: conditions of low humidity ratio are indicated with “+”

APPLICATION

Mix thoroughly the paint before applying Accelerator of curing, and then pour the content of Accelerator of curing container in the paint as specified in table below:

Name of paint / weight 
of paint per unit of 
packing, kg    
Accelerator of curing, 
number of 0.4 kg packs 
per unit of paint packing
Weight ratio of 
Accelerator of curing , 
%  
Pot life of paint after 
Accelerator of curing 
added, hrs, not less than     
Decrease of coating
drying time    
in open container in closed container 
ZINOTAN/25 kg 1 1,6 12 24 2-4 time
POLYTON-UR/ 25 kg 1 1,6 2 6 1,5-2,5 time
FERROTAN/ 15 kg 1 2,6 2 8 2-4 time
ALUMOTAN/ 17 kg 2 4,7 2 6 1,5-2,5 time

After accelerator of curing is added to the paint, mix the product again until homogeneous condition is achieved. When preparing paint in quantity deviating the standard packing strictly observe the weight ratio of components as per the table. Accelerator of curing application decreases lifetime of paint, consequently use it within the time period indicated in the table.

STORAGE AND HANDLING

Accelerator of curing is packed in plastic drums.
It shall be stored in tightly sealed manufacturer containers, away from heat sources, at temperature between plus 10 and plus 30 °С. Containers with accelerator of curing shall be protected from impact of atmospheric precipitation and direct sunlight. The shelf life in tightly sealed manufacturer containers is 6 months starting with the manufacture date.

SAFETY PRECAUTIONS

When working with accelerator of curing the related standard norms and requirements and safety measures as specified on the package label shall be observed.
Personal protective equipment (goggles, face masks, and respirators) shall be used; inhalation of solvents at their evaporation and contact with skin, ocular mucosa, and respiratory tract shall be avoided; indoor use is permitted only in case of sufficient ventilation.
The accelerator of curing is classified as a fire-hazardous product.

The information is of general character, without consideration to the object specific nature. Use of materials for other purposes not specified here or in case other influencing factors are present shall be approved by the VMP Holding CJSC in writing. In case of absence of such approval the manufacturer is not held liable for the improper use of the material and the buyer falls from the right to present claims connected with the coating quality.

Compatible materials:

You can order products and get advice of how to use materials by calling: 8-800-500-54-00, +7 343 357-30-97, 385-79-00 or by sending an On-line request

You can also purchase products from official representatives of the VMP in Russian regions, countries of near and far abroad.