REPRESENTATIVE OFFICE
IN YOUR REGION
VMP Holding CISC
Ekaterinburg,
25 Tkachey str.,

tel.: +7 343 357-30-97,
+7 343 357-30-79
e-mail: office@fmp.ru



VMP in social networks:

QUICK-DRYING
MATERIAL
ATMOSPHERE-RESISTANT
MATERIAL
HEAT-RESISTANT
MATERIAL
THICK-LAYERED
MATERIAL
FOR APPLICATION AT
NEGATIVE
TEMPERATURE
SINGLE-PACKED
MATERIAL
ST 2, ST 3 SURFACE
PREPARATION DEGREE
FOR USE AT
SEA AND FRESH
WATER
FOR USE WHEN
EXPOSED TO OIL
AND OIL PRODUCTS
ZINC-FILLED
MATERIAL
MATERIAL WITH
ANTICORROSIVE
PIGMENTS
MATERIAL WITH
CORROSION INHIBITOR
MATERIAL WITH
ANTISTATIC PROPERTIES

ISOLEP®-mio enamel

ISOLEP-mio
TU 2312-050-12288779-2005
Enamel
Double-packed
Colour: Homogeneous semi-matte gray or mustard color (the shade is not standardized)

Description

Double-packed epoxy enamel, consisting of a base and hardener (aliphatic polyamine resin); contains "iron" mica.

Recommended use

Anticorrosive protection of steel articles and structures operated in the atmospheric conditions of all macroclimatic areas, types of environment and placement categories according to GOST 15150.
Enamel is used in complex coating systems as:

  • intermediate layer;
  • topcoat in the absence of intensive exposure to solar radiance (not recommended to use as a finishcoat under the conditions of open air, I placement category according to GOST 15150). 
The coating on the basis of enamel withstands oil and oil products spills, solutions of salts, acids and alkalis; waterproof.
Enamel is recommended for application in coating systems with ZINEP® (TU 20.30.12-022-12288779- 2018), ISOLEP®-primer (TU 2312-067-12288779-2008), ZFES® (TU 20.30.12-004-12288779-2017) and with other epoxy or silicone primers.
As finishing coat it is recommended to use the POLYTON®-UR (UV) (TU 20.30.12-033-1228879-2018) and POLYTON®-UR (TU 2312-029-12288779-2002) and other enamels on polyurethane and epoxy bases.

Certificates, approvals

Certificate of state registration No. RU.66.01.40.015.Е.000134.12.10 dated 03.12.2010.
Standard STO-01393674-007-2011 Central Research Institute of Transport Construction JSC, standard STO-12288779-001-2013 of Avtodor State Company.
The decision of Lakokraspokrytiye NGO, Khotkovo

Surface preparation

  • the surface shall be pre-primed;
  • degreasing (if required) to the 1 grade according to GOST 9.402;
  • remove moisture, dust.

Application

  • mix the enamel base to a homogeneous condition;
  • add a hardener to the enamel base with constant stirring (base – hardener mixing ratio 5.2:1 by mass, 3:1 by volume), after mixing, the enamel is ready for application;
  • dilute with the thinner to the working viscosity, if necessary.
The enamel should be applied at plant and field conditions at temperatures from minus 10 to plus 40 °C and relative air humidity not exceeding 85 %.

Storage and handling

The enamel is delivered in packages: base and hardener packed in metal buckets and metal cans respectively depending on the set weight.
Storage and transportation conditions of enamel components – according to GOST 9980.5 (at air temperature from minus 40 to plus 40 °C). The container shall be protected from atmospheric condensation and direct sunlight.
Shelf life of the enamel components in hermetically enclosed original containers: base – 12 months and hardener – 18 months starting with the manufacture date.

Precautions

When working with the enamel, one shall observe the existing sectoral standard norms and requirements and safety measures as specified on the package label.
Personal protective equipment (goggles, face masks and respirators) shall be used, inhalation of thinners and contact of the composition or its components with skin, ocular mucosa, respiratory channels shall be avoided; use inside the premises is allowed only in case sufficient ventilation is provided.
The enamel is classified as a fire-hazardous material. 

The information is of general character, without consideration to the object specific nature. Use of materials for other purposes not specified here or in case other influencing factors are present shall be approved by the  VMP Holding CJSC  in writing. In case of absence of such approval the manufacturer is not held liable for the improper use of the material and the buyer falls from the right to present claims connected with the coating quality.

Compatible materials:

You can order products and get advice of how to use materials by calling: 8-800-500-54-00, +7 343 357-30-97, 385-79-00 or by sending an On-line request

You can also purchase products from official representatives of the VMP in Russian regions, countries of near and far abroad.