REPRESENTATIVE OFFICE
IN YOUR REGION
VMP Holding JSC
Ekaterinburg,
25 Tkachey str.,

tel.: +7 343 357-30-97,
+7 343 357-30-79
e-mail: office@fmp.ru



VMP in social networks:

QUICK-DRYING
MATERIAL
ATMOSPHERE-RESISTANT
MATERIAL
HEAT-RESISTANT
MATERIAL
THICK-LAYERED
MATERIAL
FOR APPLICATION AT
NEGATIVE
TEMPERATURE
SINGLE-PACKED
MATERIAL
ST 2, ST 3 SURFACE
PREPARATION DEGREE
FOR USE AT
SEA AND FRESH
WATER
FOR USE WHEN
EXPOSED TO OIL
AND OIL PRODUCTS
ZINC-FILLED
MATERIAL
MATERIAL WITH
ANTICORROSIVE
PIGMENTS
MATERIAL WITH
CORROSION INHIBITOR
MATERIAL WITH
ANTISTATIC PROPERTIES
MainAnticorrosive protectionAnticorrosive materialsBY MATERIALPrimersISOLEP®-pro penetrating primer

ISOLEP®-pro penetrating primer

ISOLEP®-pro
TU 20.30.22-124-12288779-2019
penetrating primer
Double-packed
Colour: Homogeneous transparent matted

Description

Two-component polyamide cured epoxy primer with high penetration and adhesion promoters for concrete.

Recommended use

Designed to protect concrete and reinforced concrete structures operating in the atmosphere and in contact with liquid, in areas of complete immersion and variable level.

It is used as a primer coat before applying the main coating. It is well absorbed, strengthens the surface layer of concrete. It can be used as a single coat system for dedusting a concrete surface.

ISOLEP-pro is recommended for application in coating systems with VMP protective coatings: ISOLEP-mastic, ISOLEP-hydro, POLYTON-UR, VINICOR-62 and with other epoxy, vinyl-epoxy and polyure-thane top coats.

Certificates, Approvals

Expert statement by JSC "CNIIS".

Surface preparation

The concrete surface prepared for applying the paintwork according to SP 72.13330.2016 should be uniformly rough and not have protruding reinforcement, cracks, potholes, cavities, sagging, chipped ribs, oil stains, dirt and dust.
Operating procedures:
  • remove dirt, oil and grease;
  • remove lime (cement) milk by abrasive blasting (preferably) or mechanical abrasive cleaning (grind-er, etc.) or high-pressure hydro-blasting (at least 200 atm.);
  • remove dust.
The age of the concrete base (after laying concrete or after applying leveling mixtures) before applying ISOLEP-pro must be at least 28 days.
Residual moisture in the surface layer of 20 mm should not exceed 4 %.
The temperature of the base must be at least 3 °C above the dew point.
There should be no signs of moisture on the surface.

Application

  • stir the base to a homogeneous condition before application;
  • add a curing agent and mix 2-3 min (mixing ratio by mass 19:100, respectively), after mixing, the ISOLEP-pro is ready for application;
The primer shall be applied on dry and clean surface at temperatures from plus 10 °C to plus 35 °C and relative air humidity not exceeding 80 %.
Apply a thin layer in the minimum amount required for impregnation of the concrete surface. Avoid applying too much primer - the primed surface should not be glossy. In the case of obtaining a glossy surface before applying the main coating should be abrasive surface treatment.

Storage and handling

ISOLEP-pro is supplied as the base in 20 and curing Agent in 5 litre metal containers.

Storage conditions – according to GOST 9980.5.

ISOLEP-pro must be stored in sealed package of manufacturer at air temperature from minus 40 to plus 40 °C, away from heating sources, protected from atmospheric condensation and direct sunlight.

The primer must be transported in accordance with the requirements GOST 9980.5 at ambient temperature from minus 40 to plus 40 ° C.

The shelf life of ISOLEP-pro is 36 months starting with the manufacture date.

Precautions

When working with ISOLEP-pro one shall observe the existing sectoral standard norms and requirements and safety measures as specified on the package label.

ISOLEP-pro is intended for professional use.


The information is of general character, without consideration to the object specific nature. Use of materials for other purposes not specified here or in case other influencing factors are present shall be approved by the  VMP Holding CJSC  in writing. In case of absence of such approval the manufacturer is not held liable for the improper use of the material and the buyer falls from the right to present claims connected with the coating quality.

Compatible materials:

You can order products and get advice of how to use materials by calling: 8-800-500-54-00, +7 343 357-30-97, 385-79-00 or by sending an On-line request

You can also purchase products from official representatives of the VMP in Russian regions, countries of near and far abroad.